90 not categorized PORSCHE 993 OIL SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2005-08 - Engine (includes uncategorized and accessory items)
$7.60
Make a selection 95510756100EQ
$24.20
Make a selection 99970734840 Known as: o-ring / o-ring 42 x 4 / o-ring 42 x 4 use also: View/Change Diagram
From $2.75
Make a selection 99610733600 Known as: gasket / gasket lid View/Change Diagram
From $10.00
Make a selection 99970417350EQ Used as an oil pump seal or oil cooler seal, this is the larger ring of the two that are used. Sold individually. 2 necessary per car.
$5.50
Make a selection 99911347540
View/Change Diagram
From $10.00
Make a selection 99970417250EQ Used as an oil pump seal or oil cooler seal, this is the smaller ring of the two that are used. Sold individually. 2 necessary per car.
$3.30
Make a selection 016409399B
View/Change Diagram
From $5.00
Make a selection NLA11302950 Viton for 356 and 912 note: seal has a double lip : upper sealing edge must be trimmed prior to installation 99911302950 replaces 99911302950
$38.23
Make a selection 99610731351
View/Change Diagram
From $1.96
Make a selection 99970755440 Known as: o-ring 95 x 2.5 grease View/Change Diagram
From $2.40
Make a selection FVD721T250 This special service tool was developed for the proper installation of oil seal on flywheel side of crank shaft. Trying to do this task with any other method is risking a total engine failure by way of a damaged oil seal. Applicable: for all 996 & 986 Boxster models.
$297.00
Make a selection
$12.65
Make a selection FVD721T34C Oil seal arbor tool necessary for the installation of the oil seal on the pulley side of the crank shaft.
$93.50
Make a selection FVD721T2150
$232.10
Make a selection 99970738940 Known as: o-ring 35 x 4 View/Change Diagram
From $1.00
Make a selection 99970220650 Known as: grommet 9.5 x 18.0 x 1.2 View/Change Diagram
From $6.25
Make a selection 99610712350 Known as: gasket View/Change Diagram
From $0.50
Make a selection 90012310630 Oil drain plug copper washer for Boxster. Measures 18x24mm. Oil drain plugs use soft metals such as aluminum or copper to create a good seal. In order to prevent an oil drip after oil drain, it is necessary to replace the gasket. For oil drain plug gaskets, see aluminum and copper gaskets. View/Change Diagram
From $1.00
Make a selection 106082 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$681.94
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 10010303806 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's has very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 35+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have t...(choose a part on the right to read more)
$11,932.00
Make a selection SICOILCH1 Everything you need in a money-saving package deal! includes 12 quarts of motul classic 20w50 high zinc oil, mahle filter and all seals necessary  also includes funnel for easy pouring!Â
$148.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |